| |
Plasmatronics Solar Regulators
A charge controller,
also known as a solar regulator, is
a regulator that goes between the solar
panels and the batteries.
A charge controller is used to regulate the
voltage and current coming from the solar panels
and going to the battery. As the input voltage from
the solar array rises, the charge controller regulates
the charge to the batteries preventing any over
charging.
 Plasmatronics
make high quality negative switching regulators for
a wide variety of applications, from single panel to
large-scale systems. Made in Australia.
Plasmatronics
PR Series Solar Regulators
 Ultra
compact regulators and are ideal for small systems
up to 10 amps. So small you can install it in
the panel lead, these simple switch regulators
work very well. A good choice for single panel
installations with up to 10 amps solar current.
Available in 12 or 24 volt, for sealed or flooded
type batteries.
 •
Totally sealed construction ideal for marine applications
• Small and compact
• Suited to single panel applications
• Nickel plated screws to resist corrosion
1 year manufacturer’s
warranty |
Plasmatronics 12V 10A simple regulator
for lead acid batteries
Price: $75.00
Model: PR1210
Nominal System Voltage: 12V
Solar Charge Current Maximum: 10A
Boost Charge Maximum: 14.6V
Boost Charge Cut-In: 12.5V
Float Charge Maximum: 14V
Float Charge Cut-In: 13.4V
Maximum Self Consumption: 4mA
Cable Entry Diameter: 4.5mm
Unit Dimensions: 56x37x21mm
DOWNLOAD
PRODUCT MANUAL |
Plasmatronics 12V 10A simple regulator
for sealed or gel cell batteries
Price: $75.00
Model: PR1210L
Nominal System Voltage: 12V
Solar Charge Current Maximum: 10A
Boost Charge Maximum: 14.2V
Boost Charge Cut-In: 12.5V
Float Charge Maximum: 14V
Float Charge Cut-In: 13.4V
Maximum Self Consumption: 4mA
Cable Entry Diameter: 4.5mm
Unit Dimensions: 56x37x21mm
DOWNLOAD
PRODUCT MANUAL |
Plasmatronics 24V 10A simple regulator for
lead acid batteries
Price: $75.00
Model: PR2410
Nominal System Voltage: 24V
Solar Charge Current Maximum: 10A
Boost Charge Maximum: 29.4V
Boost Charge Cut-In: 25.0V
Float Charge Maximum: 28.2V
Float Charge Cut-In: 26.2V
Maximum Self Consumption: 6mA
Cable Entry Diameter: 4.5mm
Unit Dimensions: 56x37x21mm
DOWNLOAD
PRODUCT MANUAL |
Plasmatronics 12V 10A simpler regulator for
lead acid batteries
Price: $75.00
Model: PR2410L
Nominal System Voltage: 24V
Solar Charge Current Maximum: 10A
Boost Charge Maximum: 28.8V
Boost Charge Cut-In: 25.0V
Float Charge Maximum: 27.4V
Float Charge Cut-In: 26.9V
Maximum Self Consumption: 6mA
Cable Entry Diameter: 4.5mm
Unit Dimensions: 56x37x21mm
DOWNLOAD
PRODUCT MANUAL |
Back to top of page
Plasmatronics
PL Series Solar Regulators
The
PL series of charge controllers give you the freedom
to operate your solar  electric
system the way you want to. They offer complete
control over the charge cycle, plus an unprecented
amount of useful information about current and
past performance.
PL regulators help to protect the system with
a built in low battery disconnect switch. In addition,
the versatile event controller can switch power
on or off according to criteria set by the user.
This allows the PL to do extra tasks such as switching
a light on at night or keeping a water tank full
by operating a pump when needed.
The user can select either Pulse Width Modulation
or slow speed switching. Regulation can be done
in both series and shunt modes. Other features
include backup generator control and charging
a second battery.
 Features:
• Adjustable All settings are adjustable,
units feature voltages from 12 – 48
• Display User friendly alphanumeric LCD
gives your words to explain the numbers
• Energy Metering Shows daily charge and
discharge amp/hours
• History Records charge and load amp/hours,
max and min voltage and state of charge for last
30 days
• Generator Control A sophisticated generator
controller in included should you wish to use
an auto-start generator
• Event controller Allows loads to be turned
on or off under different conditions, ideal for
lighting, pumping, frost  control
etc.
• Protection Protected against short circuit,
reverse flow, lightning. Low battery disconnect
built in, current limit for over heat of current,
conformal coating for maximum corrosion resistance.
These regulators are simple to install and use.
Highly recommended! Available in 20 amp, 40 amp
and 60 amp sizes.
1 year manufacturer’s warranty |
Plasmatronics PL20 Solar Controller
Price: $330.00
Model: PL20
Nominal System Voltages: 12,24,32,36 & 48V
Solar Charge Current Maximum: 20A
Load Switch Current Maximum: 20A
Maximum Ambient Temperature +55C
Maximum self Consumption: 9mA
Unit Dimensions: 100x109x40mm
Unit Weight: 0.35kg
DOWNLOAD
PRODUCT MANUAL |
Plasmatronic PL40 Solar Controller
Price: $415.00
Model: PL40
Nominal System Voltages: 12,24,32,36 & 48V
Solar Charge Current Maximum: 40A
Load Switch Current Maximum: 7A
Maximum Ambient Temperature +50C
Maximum self Consumption: 14mA
Unit Dimensions: 130x124x50mm
Unit Weight: 0.56kg
DOWNLOAD
PRODUCT MANUAL |
Plasmatronics PL60 Solar Controller
Price: $645.00
Model: PL60
Nominal System Voltages: 12,24,32,36 & 48V
Solar Charge Current Maximum: 60A
Load Switch Current Maximum: 30A
Maximum Ambient Temperature +50C
Maximum self Consumption: 20mA
Unit Dimensions: 228x176x62mm
Unit Weight: 1.12kg
DOWNLOAD
PRODUCT MANUAL |
|
Back to top of page
Plasmatronics
Dingo
The Plasmatronics Dingo charge controller is the
next generation of controllers. Inheriting many
of the features of the PL series, just to list
a few - More data storage (512 Days!), Negative
Ground (to suit mobile applications), enhanced
one button interface, LED backlight for LCD Display,
Hidden wiring and much more!
Features:
# Reliable, easy to understand, one button interface
and proven, easy to learn menu structure.
# Symmetrical charge and load currents, both 20A.
# Industry standard four stage charging regime.
# 12,24,32,36 and 48V selectable. Only one controller
to stock.
# Unbeatable high temperature performance. Full
charge and full load current, without interruption
to operation, in a 50oC ambient. All day, every
day.
# Fast, reliable, affordable, Plasmatronics Service,
long after the long warranty has expired
What's new?
Negative Ground
New Communications Bus
More Data Storage
Enhanced one button interface
LED backlighting
Hidden Wiring.
More terminals
Generator Terminals
The Accessories available so far include shunt
adaptors (DSA) and two different data adaptors
(DUSB and D232).
* The DSA reads external charge or load currents.
You can use up to 4 per system.
* The DUSB provides a USB interface to a computer.This
allows the user to download all the data from
the controller and change settings if required.
* The D232 provides an RS232 interface (DTE) designed
for remote computer access via a modem.
DOWNLOAD
PRODUCT MANUAL
1 year manufacturer’s warranty |
Plasmatronics Dingo 20/20
Price: $325.00
* Nominal System Voltages: 12,24,32,36 and 48V
* Maximum voltage BAT+ to BAT-: 100V
* Maximum 1 minute BAT+ to BAT- volta: 120V
* Maximum voltage SOL+ to BAT-: 100V
* Maximum voltage LOAD+ to BAT+: 70V
* Maximum voltage on G relay terminals: 90V
* Maximum voltage B+sense to BAT+: ±30V
* Maximum continuous charge current: 20A
* Maximum continuous load current: 20A
* Maximum load current for five minutes: 30A
* Maximum ‘G’ relay current: 300mA
* Battery temperature sensor range: -20/+70?C
* Maximum storage temperature: 70°C
* Supply current (dingo only, 12V): 9mA
* Supply current (dingo only, 60V): 15mA
* Supply current max (with access): 26mA
* Maximum power wire entry size: 16mm (6 AWG)
* Signal Connection Block 0.2 to 1.3mm (26-16AWG)
|
Back to top of page
Prices include freight
to nearest regional centre in Qld.
Freight cost to outlying areas is extra.
All prices are in Australian Dollars inclusive 10% GST.
All prices are subject to change and should be confirmed
before ordering.
|
and
